Blueprint Reading for the Machine Trades Revised 6th Edition Answer Key

Download

Skip this Video

Loading SlideShow in 5 Seconds..

Blueprint Reading for the Machine Trades, 6th Edition Unit 12: Auxiliary Views PowerPoint Presentation

Blueprint Reading for the Machine Trades, Sixth Edition Unit 12: Auxiliary Views

Design Reading for the Auto Trades, Sixth Edition Unit 12: Auxiliary Views. Russ Schultz and Larry Smith PowerPoint presentation created by LaVonne Vichlach. Auxiliary Views. Auxiliary views show the true shape True Shape is needed for dimensioning

Uploaded on Aug 10, 2014

• partial views
• reamed holes
• blind hole incorporate
• max max
• blueprint
• true shape

Download Presentation

Blueprint Reading for the Car Trades, Sixth Edition Unit 12: Auxiliary Views

- - - - - - - - - - - - - - - - - - - - - - - - - - - Eastward Northward D - - - - - - - - - - - - - - - - - - - - - - - - - - -

Presentation Transcript

---

1. Pattern Reading for the Car Trades, Sixth Edition Unit 12: Auxiliary Views Russ Schultz and Larry Smith PowerPoint presentation created by LaVonne Vichlach

2. Auxiliary Views • Auxiliary views show the true shape • True Shape is needed for dimensioning • Does non always create an additional view on a drawing • Can be used to replace one of the principal views

4. Inclined Planes • Appears every bit an edge in a principal view • True shape may be shown by projecting a view perpendicular to it • Accomplished by cartoon a primary auxiliary view • Oftentimes fatigued equally fractional views-exposing merely true shape of inclined plane

5. Inclined Planes • Fractional views may finish with short suspension lines • May terminate with visible lines where applicative • May use existing visible lines where applicable

7. Angle BRKT 1. What type of iron is specified for the casting? (Do not abridge.) Malleable Iron

8. Angle BRKT 2. What principal view did the auxiliary view replace? Right-Side View

9. Angle BRKT 3. Is the auxiliary view a partial view or is it consummate? Partial View

10. Angle BRKT 4. What view shows the existent shape of the reamed holes? Top View

11. Angle BRKT 5. What view shows the true height of the bosses? Front end View

12. Angle BRKT 6. What view shows the true shape and spacing of the tapped holes? Auxiliary View

13. Angle BRKT vii. What tap drill size is specified for the threaded holes? .312

14. Angle BRKT 8. How many threads does each pigsty contain? eight

15. Bending BRKT nine. What is the total tolerance on the reamed holes? .0005

16. Angle BRKT 10. What would be the overall acme of the casting before machining? ane.62

17. Angle BRKT Determine the dimensions for the alphabetic character A-Max Max: .33

18. Angle BRKT Determine the dimensions for the letter B 60°

19. Angle BRKT Determine the dimensions for the letter C .70

20. Angle BRKT Decide the dimensions for the letter D .65

21. Angle BRKT Determine the dimensions for the letter Eastward .10

22. Angle BRKT Decide the dimensions for the alphabetic character F .67

23. Angle BRKT Make up one's mind the dimensions for the letter G .38

24. Angle BRKT Determine the dimensions for the letter H .xxx

25. Angle BRKT Decide the dimensions for the letter I .45

26. Angle BRKT Decide the dimensions for the letter J .50

27. ADJ MTG Bending one. Is the auxiliary view a complete view or a partial view? Fractional View

28. ADJ MTG Bending 2. Are the tapped holes true shape or elliptical on the auxiliary view? True Shape

29. ADJ MTG ANGLE 3. Would the tapped holes be round or elliptical on the principal view? Elliptical

30. ADJ MTG Angle 4. What is the major thread diameter of the tapped holes? .375

31. ADJ MTG ANGLE v. What size tap drill is specified? .312

32. ADJ MTG ANGLE 6. What thread series is specified? Fibroid

33. ADJ MTG Bending vii. What is the pitch of the thread? (Reply decimally.) .0625

34. ADJ MTG Angle 8. What class of fit may be assumed for the threaded holes? Grade 2

35. ADJ MTG ANGLE 9. How many full threads volition the blind hole contain? 12

36. ADJ MTG ANGLE x. What blazon of section is used to expose the bullheaded holes? Broken Out

37. ADJ MTG Bending 11. What type of section is used to evidence the radius on the rib? Revolved

38. ADJ MTG ANGLE 12. How much textile remains betwixt the side of the slotted hole and the ribs? .4245

39. ADJ MTG ANGLE 13. What is the overall length of the slotted hole? 3.531

40. ADJ MTG ANGLE xiv. What size fasteners are intended for utilise in the slotted holes? .500

41. ADJ MTG Bending Determine the dimension for the letter A 1.00

42. ADJ MTG Bending Make up one's mind the dimension for the letter of the alphabet B 1.00

43. ADJ MTG Angle Make up one's mind the dimension for the letter of the alphabet C .62

44. ADJ MTG ANGLE Determine the dimension for the letter of the alphabet D i.250

45. ADJ MTG Bending Determine the dimension for the alphabetic character E-Max Max: six.53

46. ADJ MTG Angle Determine the dimension for the letter F-Max Max: 4.025

47. ADJ HOLDER BRKT one. What blazon of sectional view is the left-side view? Total

48. ADJ HOLDER BRKT 2. How many auxiliary views does the part contain? 2

49. ADJ HOLDER BRKT iii. What is the pitch of the threads tapped into the tee-slot? (three decimal places.) .036

50. ADJ HOLDER BRKT 4. Do the coarse threads require a larger or smaller tap drill than the fine threads? Smaller

cornettallasted.blogspot.com

Source: https://www.slideserve.com/sammy/blueprint-reading-for-the-machine-trades-sixth-edition-unit-12-auxiliary-views

Share this post